FSHKLE55-Z10C_10G SFP+_SFP Optical Transceivers_Products

FSHKLE55-Z10C

SFP+10Gb/s 1550nm 100km DDMI

Product Features:
Up to 11.3Gbps Data Links;
Cooled 1550nm EML laser transmitter and APD/TIA receiver;
Maximum link length of 100km on 9/125um SMF;
Hot-pluggable SFP+ footprint;
Duplex LC receptacles;
Low power dissipation;
RoHS compliant and lead-free;
Support Digital Diagnostic Monitor interface;
Single +3.3V power supply;
Compliant with SFF-8472;
Case operating temperature: Commercial: 0°C to +70°C

Back to list

Product Overview Product Features Specifications

Overview

I. Pin Diagram

Pinout of Connector Block on Host Board

II. Pin Descriptions

Pin	Symbol	Name/Description	Ref.
1	V EET	Transmitter Ground (Common with Receiver Ground)	1
2	T FAULT	Transmitter Fault.	2
3	T DIS	Transmitter Disable. Laser output disabled on high or open.	3
4	SDA	2-wire Serial Interface Data Line	4
5	SCL	2-wire Serial Interface Clock Line	4
6	MOD_ABS	Module Absent. Grounded within the module	4
7	RS0	No connection required
8	LOS	Loss of Signal indication. Logic “0” indicates normal operation.	5
9	RS1	No connection required
10	V EER	Receiver Ground (Common with Transmitter Ground)	1
11	V EER	Receiver Ground (Common with Transmitter Ground)	1
12	RD-	Receiver Inverted DATA out. AC Coupled
13	RD+	Receiver Non-inverted DATA out. AC Coupled
14	V EER	Receiver Ground (Common with Transmitter Ground)	1
15	V CCR	Receiver Power Supply
16	V CCT	Transmitter Power Supply
17	V EET	Transmitter Ground (Common with Receiver Ground)	1
18	TD+	Transmitter Non-Inverted DATA in. AC Coupled.
19	TD-	Transmitter Inverted DATA in. AC Coupled.
20	V EET	Transmitter Ground (Common with Receiver Ground)	1

Notes:

1. Circuit ground is internally isolated from chassis ground.

2. TFAULT is an open collector/drain output, which is pulled up with a 4.7kΩ – 10kΩ resistor on the host board, but is grounded inside the SFP+ cable plug.

3. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.

4. Should be pulled up with 4.7kΩ – 10kΩ on host board to a voltage between 2.0V and 3.6V. MOD_ABS pull line low to indicate module is plugged in.

5. LOS is open collector output. Should be pulled up with 4.7kΩ – 10kΩ on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.

III. Absolute Maximum Ratings

Parameter	Symbol	Min	Type	Max	Unit	Ref.
Maximum Supply Voltage	Vcc	-0.5		3.6	V
Storage Temperature	TS	-40		85	℃
Case Operating Temperature	TOP	0		70	℃	Commercial
Relative Humidity	RH	0		85	%	1

Notes:

1.Non-condensing.

IV. Optical Characteristics (TOP = 0°C to 70°C, VCC = 3.3 ± 5% Volts)

Parameter	Symbol	Min.	Typ.	Max.	Unit	Ref.
Transmitter
Center Wavelength	λc	1530	1550	1565	nm
Spectral Width(-20dB)	Pm			1	nm
Side-mode Suppression Ratio	SMSR	30			dB
Average Output Power	Pavg	0		4	dBm
Extinction Ratio	ER	9			dB
Return Loss		12			Db
Transmitter OFF Output Power	Poff			-30	dBm
Transmitter and Dispersion Peralty	TDP			3	dB
Receiver
Center Wavelength	λc	1260		1600	nm
Receiver Sensitivity, Average Power				-24	dBm	1
Receiver Saturation Power	Psat			-8	dBm
Loss of Signal Assert	PA	-35			dBm
Loss of Signal De-assert	PD			-26	dBm
LOS Hysteresis	PD- PA	0.5			dB

Notes:

1. Measured with a PRBS 2^31-1 test pattern, @ 10.3125Gb/s, BER<1E-12.

V. Electrical Characteristics (TOP = 0°C to 70°C, VCC = 3.3 ± 5% Volts)

Parameter	Symbol		Min		Type	Max	Unit		Ref.
Supply Voltage	Vcc		3.135		3.3	3.465	V
Supply Current	Icc					450	mA
Transmitter
Input differential impedance	Rin				100				1
Differential data input swing	Vin, pp		200			1000	mV
Transmit Disable Voltage	VD		2			VCC	V
Transmit Enable Voltage	VEN		Vee			Vee+0.8	V
Receiver
Differential data output swing	Vout, pp		200			1000	mV		2
LOS Fault	VLOS_fault		2			Vcc	V		3
LOS Normal	VLos_nom		Vee			Vee+0.8	V		3
Power Supply Noise Tolerance		VccT/VccR		Per SFP MSA				mVpp

Notes:

1. Connected directly to TX data input pins.AC coupling from pins into laser driver IC.

2. Into 100Ω differential termination.

3. Loss Of Signal is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected.

VI. Digital Diagnostic Memory Map

VII. Digital Diagnostic Monitoring Information

Parameter	Unit	Accuracy
Case Temperature	℃	±3
Supply Voltage	V	±3%
Tx Bias Current	mA	±10%
Tx Optical Power	dB	±3
Rx Optical Power	dB	±3

VIII. Recommended Interface Circuit

IX. Mechanical Specifications

SFP wire mechanical drawing (Unit: mm)

feature

Product Features

Up to 11.3Gbps Data Links

Cooled 1550nm EML laser transmitter and APD/TIA receiver

Maximum link length of 100km on 9/125um SMF

Hot-pluggable SFP+ footprint

Duplex LC receptacles

Low power dissipation

RoHS compliant and lead-free

Support Digital Diagnostic Monitor interface

Single +3.3V power supply

Compliant with SFF-8472

Case operating temperature: Commercial: 0°C to +70°C

Applications

Compliance

10GBASE-ZR/ZW 10G Ethernet

SFP MSA

1Gb/s,2Gb/s,4Gb/s,8Gb/s and 10Gb/s Fibre Channel

CPRI Rates 10. 138 Gb/s, 9.830 Gb/s

7.373 Gb/s, 6. 144 Gb/s, 4.915 Gb/s

2.458 Gb/s, 1.229 Gb/s, 0.614 Gb/s

Specifications

Ordering Information

Part No.

Bit Rate

(Gbps)

Laser

(nm)

Distance（km）

Fiber

Type

DDMI

Connector

Temp

FSHKLE55-Z10C

10.3125

1550

100

SMF

YES

0℃~70℃