Product Features:
Up to 10.3125Gbps Data Links;
1490nm /1550 Cooled EML laser transmitter and APD/TIA receiver;
Maximum link length of 80km on 9/125um SMF;
Hot-pluggable SFP+ footprint;
LC receptacles;
Low power dissipation;
RoHS compliant and lead-free;
Support Digital Diagnostic Monitor interface;
Single +3.3V power supply;
Compliant with SFF-8472;
Case operating temperature: Commercial: 0°C to +70°C; Industrial: -40°C to +85°C
I. Pin Diagram
Pinout of Connector Block on Host Board
II. Pin Descriptions
Pin | Symbol | Name/Description | Ref. |
1 | V EET | Transmitter Ground (Common with Receiver Ground) | 1 |
2 | T FAULT | Transmitter Fault. | 2 |
3 | T DIS | Transmitter Disable. Laser output disabled on high or open. | 3 |
4 | SDA | 2-wire Serial Interface Data Line | 4 |
5 | SCL | 2-wire Serial Interface Clock Line | 4 |
6 | MOD_ABS | Module Absent. Grounded within the module | 4 |
7 | RS0 | No connection required | |
8 | LOS | Loss of Signal indication. Logic “0” indicates normal operation. | 5 |
9 | RS1 | No connection required | |
10 | V EER | Receiver Ground (Common with Transmitter Ground) | 1 |
11 | V EER | Receiver Ground (Common with Transmitter Ground) | 1 |
12 | RD- | Receiver Inverted DATA out. AC Coupled | |
13 | RD+ | Receiver Non-inverted DATA out. AC Coupled | |
14 | V EER | Receiver Ground (Common with Transmitter Ground) | 1 |
15 | V CCR | Receiver Power Supply | |
16 | V CCT | Transmitter Power Supply | |
17 | V EET | Transmitter Ground (Common with Receiver Ground) | 1 |
18 | TD+ | Transmitter Non-Inverted DATA in. AC Coupled. | |
19 | TD- | Transmitter Inverted DATA in. AC Coupled. | |
20 | V EET | Transmitter Ground (Common with Receiver Ground) | 1 |
Notes:
1. Circuit ground is internally isolated from chassis ground.
2. TFAULT is an open collector/drain output, which is pulled up with a 4.7kΩ – 10kΩ resistor on the host board, but is grounded inside the SFP+ cable plug.
3. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
4. Should be pulled up with 4.7kΩ – 10kΩ on host board to a voltage between 2.0V and 3.6V. MOD_ABS pull line low to indicate module is plugged in.
5. LOS is open collector output. Should be pulled up with 4.7kΩ – 10kΩ on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
III. Absolute Maximum Ratings
Parameter | Symbol | Min | Type | Max | Unit | Ref. |
Maximum Supply Voltage | Vcc | -0.5 | 3.6 | V | ||
Storage Temperature | TS | -40 | 85 | ℃ | ||
Case Operating Temperature |
TOP | 0 | 70 |
℃ | Commercial | |
-40 | 85 | Industrial | ||||
Relative Humidity | RH | 5 | 95 | % | 1 |
Notes:
1.Non-condensing.
IV. Optical Characteristics (TOP = 0°C to 70°C, VCC = 3.3 ± 5% Volts)
Parameter | Symbol | Min. | Typ. | Max. | Unit | Remark |
Transmitter | ||||||
Center Wavelength | λc | 1480 | 1490 | 1500 | nm | FSHKLE45-K80 |
1540 | 1550 | 1560 | FSHKLE54-K80 | |||
Spectral Width(-20dB) | Pm | 1 | nm | |||
Side-mode Suppression Ratio | SMSR | 30 | dB | |||
Average Output Power | Pavg | 0 | 4 | dBm | ||
Extinction Ratio | ER | 9 | dB | |||
Return Loss | 12 | dB | ||||
Transmitter OFF Output Power | POff | -30 | dBm | |||
Receiver | ||||||
Center Wavelength | λc | 1540 | 1550 | 1560 | nm | FSHKLE45-K80 |
1480 | 1490 | 1500 | FSHKLE54-K80 | |||
Receiver Sensitivity, Average Power | -24 | dBm | 1 | |||
Receiver Saturation Power | Psat | -8 | dBm | |||
Loss of Signal Assert | PA | -35 | dBm | |||
Loss of Signal De-assert | PD | -26 | dBm | |||
LOS Hysteresis | PD- PA | 0.5 | dB | |||
Notes:
1. Measured with a PRBS 2^31-1 test pattern, @ 10.3125Gb/s, BER<1E-12.
V. Electrical Characteristics (TOP = 0°C to 70°C, VCC = 3.3 ± 5% Volts)
Parameter | Symbol | Min | Type | Max | Unit | Ref. | ||||||||
Supply Voltage | Vcc | 3.135 | 3.3 | 3.465 | V | |||||||||
Supply Current | Icc | 450 | mA | |||||||||||
Transmitter | ||||||||||||||
Input differential impedance | Rin | 100 | 1 | |||||||||||
Differential data input swing | Vin, pp | 200 | 1000 | mV | ||||||||||
Transmit Disable Voltage | VD | 2 | VCC | V | ||||||||||
Transmit Enable Voltage | VEN | Vee | Vee+0.8 | V | ||||||||||
Receiver | ||||||||||||||
Differential data output swing | Vout, pp | 200 | 1000 | mV | 2 | |||||||||
LOS Fault | VLOS_fault | 2 | Vcc | V | 3 | |||||||||
LOS Normal | VLOS_norm | Vee | Vee+0.8 | V | 3 | |||||||||
Power Supply Noise Tolerance | VCCT/VCCR | Per SFF-8431 | mVpp | |||||||||||
Notes:
1. Connected directly to TX data input pins.AC coupling from pins into laser driver IC.
2. Into 100Ω differential termination.
3. Loss Of Signal is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected.
VI. Digital Diagnostic Memory Map
VII. Digital Diagnostic Monitoring Information
Parameter | Unit | Accuracy |
Case Temperature | ℃ | ±3 |
Supply Voltage | V | ±3% |
Tx Bias Current | mA | ±10% |
Tx Optical Power | dB | ±3 |
Rx Optical Power | dB | ±3 |
VIII. Recommended Interface Circuit
IX. Mechanical Specifications
SFP wire mechanical drawing (Unit: mm)
Product Features
Up to 10.3125Gbps Data Links
1490nm /1550 Cooled EML laser transmitter and APD/TIA receiver
Maximum link length of 80km on 9/125um SMF
Hot-pluggable SFP+ footprint
LC receptacles
Low power dissipation
RoHS compliant and lead-free
Support Digital Diagnostic Monitor interface
Single +3.3V power supply
Compliant with SFF-8472
Case operating temperature: Commercial: 0°C to +70°C; Industrial: -40°C to +85°C
Applications | Compliance |
10GBASE-ZR/ZW 10G Ethernet | SFP MSA |
1Gb/s,2Gb/s,4Gb/s,8Gb/s and 10Gb/s Fibre Channel CPRI Rates 10. 138 Gb/s, 9.830 Gb/s 7.373 Gb/s, 6. 144 Gb/s, 4.915 Gb/s 2.458 Gb/s, 1.229 Gb/s, 0.614 Gb/s Other Optical Links | SFP-8472 RoHS IEEE802.3ae |
Ordering Information
Part No. | Bit Rate (Gbps) | Laser (nm) | Distance（km） | Fiber Type | DDMI | Connector | Temp |
FSHKLE45-K80C | 10.3125 | 1550 | 80 | SMF | YES | LC | 0℃~70℃ |
FSHKLE54-K80C | 10.3125 | 1490 | 80 | SMF | YES | LC | 0℃~70℃ |