FSANMM85-S15C_40G QSFP+_SFP Optical Transceivers_Products

FSANMM85-S15C

QSFP+ 40Gb/s SR4 150m DDM

Product Features:
l Multi rate of up to 10.3125Gb/s per channel;
l Transmission distance up to150m OM3;
l Hot-pluggable QSFP+ footprint;
l Single 1x12 MPO receptacle;
l Low power consumption;
l Four-channel full-duplex transceiver module;
l RoHS-6 compliant and lead-free;
l +3.3V single power supply;
l Support Digital Diagnostic Monitor interface;
l Case operating temperature:
Commercial: 0°C to +70°C

Back to list

Product Overview Product Features Specifications

Overview

I. Pin Diagram

II. Pin Descriptions

Pin	Symbol	Name/Description	Ref.
1	GND	Ground	1
2	Tx2n	Transmitter Inverted Data Input
3	Tx2p	Transmitter Non-Inverted Data Input
4	GND	Ground	1
5	Tx4n	Transmitter Inverted Data Input
6	Tx4p	Transmitter Non-Inverted Data Input
7	GND	Ground	1
8	ModSe1L	Module Select
9	ResetL	Module Reset
10	Vcc Rx	+3.3V Power supply receiver
11	SCL	2-wire serial interface clock
12	SDA	2-wire serial interface data
13	GND	Ground	1
14	Rx3p	Receiver Non-Inverted Data Output
15	Rx3n	Receiver Inverted Data Output
16	GND	Ground	1
17	Rx1p	Receiver Non-Inverted Data Output
18	Rx1n	Receiver Inverted Data Output
19	GND	Ground	1
20	GND	Ground	1
21	Rx2n	Receiver Inverted Data Output
22	Rx2p	Receiver Non-Inverted Data Output
23	GND	Ground	1
24	Rx4n	Receiver Inverted Data Output
25	Rx4p	Receiver Non-Inverted Data Output
26	GND	Ground	1
27	ModPrSL	Module Present
28	IntL	Interrupt
29	VccTx	+3.3V Power supply transmitter
30	Vcc1	+3.3V Power Supply
31	LPMode	Low Power Mode
32	GND	Ground	1
33	Tx3p	Transmitter Non-Inverted Data Input
34	Tx3n	Transmitter Inverted Data Input
35	GND	Ground	1
36	Tx1p	Transmitter Non-Inverted Data Input
37	Tx1n	Transmitter Inverted Data Input
38	GND	Ground	1

Notes：

1. Circuit ground is internally isolated from chassis ground.

III. Absolute Maximum Ratings

Parameter	Symbol	Min.	Typ.	Max.	Unit	Ref.
Storage Temperature	T_S	-40		85	ºC
Storage Ambient Humidity	H_A	0		85	%
Maximum Supply Voltage	V_CC1, V_CCT_X, V_CCR_X	-0.5		3.6	V
Signal Input Voltage		-0.3		4.0	V
Receiver Damage Threshold		+3.8			dBm
Lead Soldering Temperature/Time	TSOLD			260/10	ºC/sec	1
Lead Soldering Temperature/Time	TSOLD			360/10	ºC/sec	2

Notes:

1.Suitable for wave soldering.

2. Only for soldering by iron.

IV. Optical Characteristics

Parameter	Symbol	Min.	Typ.	Max.	Unit	Ref.
Transmitter(per Lane)
Average Output Power	POUT	-6		2.4	dBm
Extinction Ratio	ER	3.0			dB
Center Wavelength	λC	840		860	nm
RMS Spectral Width	σ			0.6	nm
Transmitter OFF Output Power	POff			-30	dBm
Relative Intensity Noise	RIN			-128	dB/Hz
Transmitter eye mask definition {X1,X2,X3,Y1,Y2,Y3}		0.23,0.34,0.43,0.27,0.35,0.4
Receiver(per Lane)
Input Optical Wavelength	λIN	840		860	nm
Rx Sensitivity per lane	RSENS			-10.3	dBm	@BER=1E-12
Input Saturation Power (Overload)	PSAT	+2.4			dBm	1
Loss of Signal Assert	PA	-30			dBm
Loss of Signal De-assert	PD			-12	dBm
LOS Hysteresis	PD - PA	0.5		6	dB

Notes:

1. Measured with PRBS 2^31- 1 test pattern @10.3125Gbps.BER=1E- 12.

V. Electrical Interface Characteristics

Parameter	Symbol	Min.	Typ.	Max.	Unit	Ref.
Supply Voltage	VCC 1, VCCTX, VCCRX	3.15		3.45	V
Supply Current	ICC			350	mA
Transmitter(per Lane)
Input different impedance	Rin	90	100	110	Ω	1
Single ended input voltage tolerance	VinT	-0.3		4.0	V
Single ended data input swing	Vin,pp	200		1000	mV	2
Receiver (per Lane)
Output different impedance	Rout	90	100	110	Ω	1
Single ended data output swing	Vout,pp	200		1000	mV	3
Single-ended output voltage	VoutR	-0.3		4.0	V

Note :

1.Connected directly to TX data input pins. AC coupled thereafter.

2. After internal AC coupling. Self-biasing 100Ω differential input

3.Into 100Ω differential termination.

VI. Memory Map and Control Registers

Compatiable with SFF-8436Rev.4.8(QSFP+).

VII. Recommended Interface Circuit

VIII.Mechanical Specifications (Unit: mm)

feature

Product Features

l Multi rate of up to 10.3125Gb/s per channel

l Transmission distance up to150m OM3

l Hot-pluggable QSFP+ footprint

l Single 1x12 MPO receptacle

l Low power consumption

l Four-channel full-duplex transceiver module

l RoHS-6 compliant and lead-free

l +3.3V single power supply

l Support Digital Diagnostic Monitor interface

l Case operating temperature:

Commercial: 0°C to +70°C

Applications	Compliance
40GBASE-SR4 40G Ethernet	QSFP+ MSA.
InfiniBand QDR	IEEE802.3ba
Other optical links	SFF-8436
	RoHS

Specifications

Ordering Information

Part NO.

Bit Rate

(Gbps)

Laser

(nm)

Distance(

Media

DDMI

Connector

Temp(℃)

FSANMM85-S15C

850

150

multi-mode fiber

YES

MPO 1X12

0~70