FSANLC23-K40C_40G QSFP+_SFP Optical Transceivers_Products

FSANLC23-K40C

QSFP+ 40Gb/s ER4 40km DDMI

Product Features:
l Hot-pluggable QSFP+ form factor;
l Supports 41.3 Gb/s aggregate bit rate;
l Power dissipation < 3.5W;
l 18.5 dB link insertion loss budget;
l RoHS-6 compliant;
l Single 3.3V power supply;
l Maximum link length of 40km on Single Mode Fiber (SMF);
l Uncooled 4x10Gb/s CWDM transmitter;
l XLPPI electrical interface;
l Duplex LC receptacles;
l Built-in digital diagnostic functions, including Tx/Rx power;
l Commercial: 0°C to +70°C

Back to list

Product Overview Product Features Specifications

Overview

I. Pin Diagram

II. Pin Descriptions

Pin	Symbol	Name/Description	Ref.
1	GND	Ground	1
2	Tx2n	Transmitter Inverted Data Input
3	Tx2p	Transmitter Non-Inverted Data Input
4	GND	Ground	1
5	Tx4n	Transmitter Inverted Data Input
6	Tx4p	Transmitter Non-Inverted Data Input
7	GND	Ground	1
8	ModSe1L	Module Select
9	ResetL	Module Reset
10	Vcc Rx	+3.3V Power supply receiver
11	SCL	2-wire serial interface clock
12	SDA	2-wire serial interface data
13	GND	Ground	1
14	Rx3p	Receiver Non-Inverted Data Output
15	Rx3n	Receiver Inverted Data Output
16	GND	Ground	1
17	Rx1p	Receiver Non-Inverted Data Output
18	Rx1n	Receiver Inverted Data Output
19	GND	Ground	1
20	GND	Ground	1
21	Rx2n	Receiver Inverted Data Output
22	Rx2p	Receiver Non-Inverted Data Output
23	GND	Ground	1
24	Rx4n	Receiver Inverted Data Output
25	Rx4p	Receiver Non-Inverted Data Output
26	GND	Ground	1
27	ModPrSL	Module Present
28	IntL	Interrupt
29	VccTx	+3.3V Power supply transmitter
30	Vcc1	+3.3V Power Supply
31	LPMode	Low Power Mode
32	GND	Ground	1
33	Tx3p	Transmitter Non-Inverted Data Input
34	Tx3n	Transmitter Inverted Data Input
35	GND	Ground	1
36	Tx1p	Transmitter Non-Inverted Data Input
37	Tx1n	Transmitter Inverted Data Input
38	GND	Ground	1

Notes：

1. Circuit ground is internally isolated from chassis ground.

III. Absolute Maximum Ratings

Parameter	Symbol	Min.	Typ.	Max.	Unit	Ref.
Storage Temperature	T_S	-40		85	ºC
Storage Ambient Humidity	H_A	0		85	%
Maximum Supply Voltage	V_CC1, V_CCT_X, V_CCR_X	-0.5		3.6	V
Signal Input Voltage		-0.3		4.0	V
Receiver Damage Threshold		+3.8			dBm
Lead Soldering Temperature/Time	TSOLD			260/10	ºC/sec	1
Lead Soldering Temperature/Time	TSOLD			360/10	ºC/sec	2

Notes:

1.Suitable for wave soldering.

2. Only for soldering by iron.

IV. General Product Characteristics

Parameter	Value				Unit		Ref.
Module Form Factor	QSFP+
Number of Lanes	4 Tx and 4 Rx
Maximum Aggregate Data Rate	41.2500				Gb/s
Maximum Data Rate per Lane	10.3125				Gb/s		Higher bit rates may be supported. Please contact Inphilight
Protocols Supported	40G Ethernet
Management Interface	Serial,I2c-based,400kHz maximum frequency						As defined by the QSFP+ MSA
Data Rate Specifications		Symbol	Min.	Typ.		Max.		Unit	Ref.
Bit Rate per Lane		BR				10.3125		Gb/s	1
Bit Error Ratiio		BER				10^-12			2
Link distance on SMF-28		d	0.002			40		km	3

Note:

1. ± 100 ppm,Compliant with 40GBASE-ER4 and XLPPI per IEEE 802.3bm.

2. Tested with a PRBS 231-1 test pattern.

3. Per 40GBASE-ER4, IEEE 802.3bm.Links longer than 30km are considered to be engineered links, with losses less than the worst case specified for the fiber type.

V. Optical Characteristics

Parameter	Symbol	Min.	Typ.	Max.	Unit	Ref.
Transmitter
Signaling Speed per Lane			10.3125	11.2	Gbps
Total Average Launch Power	P_OUT			10.5	dBm
Average Output Power per lane	P_OUT	-2.7		4.5	dBm
Transmit OMA per Lane	TxOMA	0.3		5.0	dBm	1
Extinction Ratio	ER	5.5			dB
Center Wavelength	λC	1264.5 1284.5 1304.5 1324.5	1271 1291 1311 1331	1277.5 1297.5 1317.5 1337.5	nm
Sidemode Suppression ratio	SMSR	30			dB
Transmitter and Dispersion Penalty	TDP			2.6	dB
Relative Intensity Noise	RIN			128	dB/Hz
Transmitter OFF Output Power	POff			-30	dBm
Transmitter eye mask definition {X1,X2,X3,Y1,Y2,Y3}		0.25,0.4,0.45,0.25,0.28,0.4
Receiver
Signaling Speed per Lane			10.3125	11.2	Gbps
Input Optical Wavelength	λ_IN	1264.5 1284.5 1304.5 1324.5	1271 1291 1311 1331	1277.5 1297.5 1317.5 1337.5	nm
Rx Sensitivity per lane	R_SENS1			-19	dBm
Input Saturation Power (Overload)	PSAT			+3.8	dBm
Receiver Reflectance	Rfl			-26	dBm
Loss of Signal Assert	P_A	-35			dBm
Loss of Signal De-assert	P_D			-19	dBm
LOS Hysteresis	P_D- P_A	0.5		6	dB

Notes:

1. Minimum value is informative.

VI. Memory Map and Control Registers

Compatible with SFF-8636 (QSFP+ MSA)

VII. Electrical Interface Characteristics

Parameter	Symbol	Min.	Typ.	Max.	Unit	Ref.
Supply Voltage	V_CC1, V_CCT_X, V_CCR_X	3.1		3.47	V
Supply Current	I_CC			1130	mA
Transmitter
Input different impedance	R_in	90	100	110	Ω	2
Single ended data input swing	Vin,pp	120		820	mV
Transmitter Disable Voltage	VDIS	2		V_CC	V	3
Transmitter Enable Voltage	VEN	0		0.8	V
Receiver
Output different impedance	R_out	90	100	110	Ω	2
Single ended data output swing	Vout,pp	340		850	mV	4
LOS Asserted	V_LOSA	2		V_CCHOST	V	5
LOS De-asserted	V_LOSD	0		0.8	V	5
Power Supply Rejection	PSR	50			mVpp

Note :

1.Maximum total power value is specified across the full temperature and voltage range.

2.Connected directly to TX data input pins. AC coupled thereafter.

3.Or open circuit.

4.Into 100Ωdifferential termination.

5.Loss Of Signal is LVTTL. Logic “0”indicates normal operation; logic “1” indicates no signal detected.

VIII. Mechanical Specifiactions

feature

Product Features

l Hot-pluggable QSFP+ form factor

l Supports 41.3 Gb/s aggregate bit rate

l Power dissipation < 3.5W

l 18.5 dB link insertion loss budget

l RoHS-6 compliant

l Single 3.3V power supply

l Maximum link length of 40km on Single Mode Fiber (SMF)

l Uncooled 4x10Gb/s CWDM transmitter

l XLPPI electrical interface

l Duplex LC receptacles

l Built-in digital diagnostic functions, including Tx/Rx power

l Commercial: 0°C to +70°C

Applications	Compliance
40GBASE-ER4 40G Ethernet	QSFP+ MSA.
	IEEE802.3bm
	SFF-8436
	RoHS

Specifications

Ordering Information

Part NO.

Bit Rate (Gbps)

Laser (nm)

Distance(km)

Media

DDMI

Connector

Temp（℃）

FSANLC23-K40C

41.3

1271nm

1291nm

1311nm

1331nm

single-mode fiber

YES

0~70