FSANLC23-K10C_40G QSFP+_SFP Optical Transceivers_Products

FSANLC23-K10C

QSFP+ 40Gb/s LR4 10km DDM

Product Features:
l Supports 41.2 Gb/s aggregate bitrates;
l Uncooled 4x10Gb/s CWDM transmitter;
l Maximum link length of 10km on Single Mode Fiber (SMF);
l Hot-pluggable QSFP+ footprint;
l Duplex LC receptacles;
l Power dissipation < 3.5W;
l RoHS-6 compliant and lead-free;
l Single 3.3V power supply;
l Support Digital Diagnostic Monitor interface;
l Case operating temperature;
l Commercial: 0°C to +70°C

Back to list

Product Overview Product Features Specifications

Overview

I. Pin Diagram

QSFP MSA-compliant 38-pinconnector

II. Pin Descriptions

Pin	Symbol	Name/Description	Notes
1	GND	Ground	1
2	Tx2n	Transmitter Inverted Data Input
3	Tx2p	Transmitter Non-Inverted Data Input
4	GND	Ground	1
5	Tx4n	Transmitter Inverted Data Input
6	Tx4p	Transmitter Non-Inverted Data Input
7	GND	Ground	1
8	ModSelL	Module Select
9	ResetL	Module Reset
10	VccRx	+3.3 V Power supply receiver
11	SCL	2-wire serial interface clock
12	SDA	2-wire serial interface data
13	GND	Ground	1
14	Rx3p	Receiver Non-Inverted Data Output
15	Rx3n	Receiver Inverted Data Output
16	GND	Ground	1
17	Rx1p	Receiver Non-Inverted Data Output
18	Rx1n	Receiver Inverted Data Output
19	GND	Ground	1
20	GND	Ground	1
21	Rx2n	Receiver Inverted Data Output
22	Rx2p	Receiver Non-Inverted Data Output
23	GND	Ground	1
24	Rx4n	Receiver Inverted Data Output
25	Rx4p	Receiver Non-Inverted Data Output
26	GND	Ground	1
27	ModPrsL	ModulePresent
28	IntL	Interrupt
29	VccTx	+3.3 V Power supply transmitter
30	Vcc1	+3.3 V Power Supply
31	LPMode	Low Power Mode
32	GND	Ground	1
33	Tx3p	Transmitter Non-Inverted Data Input
34	Tx3n	Transmitter Inverted Data Input
35	GND	Ground	1
36	Tx1p	Transmitter Non-Inverted Data Input
37	Tx1n	Transmitter Inverted Data Input
38	GND	Ground	1

Notes：

1. Circuit ground is internally isolated from chassis ground.

III. Absolute Maximum Ratings

Parameter	Symbol	Min.	Typ.	Max.	Unit	Ref.
Storage Temperature	T_S	-40		85	ºC
Storage Ambient Humidity	H_A	5		85	%
Maximum Supply Voltage	V_CC1, V_CCT_X, V_CCR_X	0		3.6	V
Signal Input Voltage		-0.3		Vcc+0.3	V
Receiver Damage Threshold	P_Rdmg	3.5			dBm
Lead Soldering Temperature/Time	TSOLD			260/10	ºC/sec	1
Lead Soldering Temperature/Time	TSOLD			360/10	ºC/sec	2

Notes:

1.Suitable for wave soldering.

2. Only for soldering by iron.

IV. Optical Characteristics

Parameter	Symbol	Min.	Typ.	Max.	Unit	Ref.
*Transmitter*
Total Average Launch Power	POUT			8.3	dBm
Average Output Power per lane	POUT	-7		2.3	dBm
Transmit OMA per Lane	TxOMA	-4.0		3.5	dBm	1
Extinction Ratio	ER	3.5			dB
Center Wavelength	λC		1264.5 - 1277.5 1284.5 - 1297.5 1304.5 - 1317.5 1324.5 - 1337.5		nm
Sidemode Suppression ratio	SMSR	30			dB
Transmitter and Dispersion Penalty	TDP			3.5	dB
Transmitter OFF Output Power	POff			-30	dBm
Transmitter eye mask definition {X1,X2,X3,Y1,Y2,Y3}		0.25,0.4,0.45,0.25,0.28,0.4
*Receiver*
Input Optical Wavelength	λIN		1264.5 – 1277.5 1284.5 – 1297.5 1304.5 – 1317.5 1324.5 – 1337.5		nm
Rx Sensitivity per lane	RSENS1			-11.5	dBm
Rx Sensitivity(OMA)	RSENS2			-9.6	dBm
Input Saturation Power (Overload)	PSAT			+3.3	dBm
Receiver Reflectance	Rfl			-12	dBm
Loss of Signal Assert	PA	-30			dBm
Loss of Signal De-assert	PD			-12.5	dBm
LOS Hysteresis	PD - PA	0.5		6	dB

Note:

1. Even if TDP is <0.9dB, the OMA min must exceed this value.

V. Memory Map and Control Registers

Compatiable with SFF-8436Rev.4.8(QSFP+).

VI. Electrical Interface Characteristics

Parameter	Symbol	Min.	Typ.	Max.	Unit	Ref.
Supply Voltage	VCC 1, VCCTX, VCCRX	3.15		3.45	V
Supply Current	ICC			350	mA
*Transmitter*
Input different impedance	Rin	90	100	110	Ω	2
Single ended data input swing	Vin,pp	120		820	mV
Transmitter Disable Voltage	VDIS	2		VCC	V	3
Transmitter Enable Voltage	VEN	0		0.8	V
*Receiver*
Output different impedance	Rout	90	100	110	Ω	2
Single ended data output swing	Vout,pp	340		850	mV	4
LOS Asserted	VLOSA	2		VCCHOST	V	5
LOS De-asserted	VLOSD	0		0.8	V	5
Power Supply Rejection	PSR	50			mVpp

Note :

1.Maximum total power value is specified across the full temperature and voltage range.

2.Connected directly to TX data input pins. AC coupled thereafter.

3. Or open circuit.

4.Into 100Ω differential termination.

5.Loss Of Signal is LVTTL. Logic “0” indicates normal operation; logic “1” indicates no signal detected.

VII. Mechanical Specifiactions

feature

Product Features

l Supports 41.2 Gb/s aggregate bitrates

l Uncooled 4x10Gb/s CWDM transmitter

l Maximum link length of 10km on Single Mode Fiber (SMF)

l Hot-pluggable QSFP+ footprint

l Duplex LC receptacles

l Power dissipation < 3.5W

l RoHS-6 compliant and lead-free

l Single 3.3V power supply

l Support Digital Diagnostic Monitor interface

l Case operating temperature

l Commercial: 0°C to +70°C

Applications

Compliance

40GBASE-LR4 40G Ethernet

QSFP+ MSA.

IEEE802.3ba

SFF-8436

RoHS

Specifications

Ordering Information

Part NO.

Bit Rate

(Gbps)

Laser (nm)

Distance(

km)

Media

DDMI

Connector

Temp(℃)

FSANLC23-K10C

10.3125

1271nm 1291nm 1311nm

1331nm

single-mode fiber

YES

0~70