FSANLC23-K02C_40G QSFP+_SFP Optical Transceivers_Products

FSANLC23-K02C

QSFP+ 40Gb/s LR4 02km DDM

Product Features:
l Supports 41.2 Gb/s aggregate bitrates;
l Uncooled 4x10Gb/s CWDM transmitter;
l Maximum link length of 150m on OM3, 160m on OM4, and;
l 2km on Single Mode Fiber (SMF);
l Hot-pluggable QSFP+ footprint;
l Duplex LC receptacles;
l Power dissipation < 3.5W;
l Compliant to the SFF-8636 Common Management Interface MSA;
l Single 3.3V power supply;
l Support Digital Diagnostic Monitor interface;
l Case operating temperature;
Commercial: 0°C to +70°C

Back to list

Product Overview Product Features Specifications

Overview

I. Pin Diagram

QSFP MSA-compliant 38-pinconnector

II. Pin Descriptions

Pin	Symbol	Name/Description	Notes
1	GND	Ground	1
2	Tx2n	Transmitter Inverted Data Input
3	Tx2p	Transmitter Non-Inverted Data Input
4	GND	Ground	1
5	Tx4n	Transmitter Inverted Data Input
6	Tx4p	Transmitter Non-Inverted Data Input
7	GND	Ground	1
8	ModSelL	Module Select
9	ResetL	Module Reset
10	VccRx	+3.3 V Power supply receiver
11	SCL	2-wire serial interface clock
12	SDA	2-wire serial interface data
13	GND	Ground	1
14	Rx3p	Receiver Non-Inverted Data Output
15	Rx3n	Receiver Inverted Data Output
16	GND	Ground	1
17	Rx1p	Receiver Non-Inverted Data Output
18	Rx1n	Receiver Inverted Data Output
19	GND	Ground	1
20	GND	Ground	1
21	Rx2n	Receiver Inverted Data Output
22	Rx2p	Receiver Non-Inverted Data Output
23	GND	Ground	1
24	Rx4n	Receiver Inverted Data Output
25	Rx4p	Receiver Non-Inverted Data Output
26	GND	Ground	1
27	ModPrsL	ModulePresent
28	IntL	Interrupt
29	VccTx	+3.3 V Power supply transmitter
30	Vcc1	+3.3 V Power Supply
31	LPMode	Low Power Mode
32	GND	Ground	1
33	Tx3p	Transmitter Non-Inverted Data Input
34	Tx3n	Transmitter Inverted Data Input
35	GND	Ground	1
36	Tx1p	Transmitter Non-Inverted Data Input
37	Tx1n	Transmitter Inverted Data Input
38	GND	Ground	1

Notes：

1. Circuit ground is internally isolated from chassis ground.

III. Absolute Maximum Ratings

Parameter	Symbol	Min.	Typ.	Max.	Unit	Ref.
Storage Temperature	T_S	-40		85	ºC
Storage Ambient Humidity	H_A	5		85	%
Maximum Supply Voltage	V_CC1, V_CCT_X, V_CCR_X	0		3.6	V
Signal Input Voltage		-0.3		Vcc+0.3	V
Receiver Damage Threshold	P_Rdmg	3.5			dBm
Lead Soldering Temperature/Time	TSOLD			260/10	ºC/sec	1
Lead Soldering Temperature/Time	TSOLD			360/10	ºC/sec	2

Notes:

1.Suitable for wave soldering.

2. Only for soldering by iron.

IV. Optical Characteristics

Parameter	Symbol	Min.	Typ.	Max.	Unit	Ref.
*Transmitter*
Signaling rate, each lane	10.3125				Gb/s
Total Average Launch Power MMF				9.5	dBm
Total Average Launch Power SMF				8.3	dBm
Average Output Power per lane,MMF	TxPx	-5.0		3.5	dBm
Average Output Power per lane,SMF	TxPx	-7.0		2.3	dBm
Optical Modulation Amplitude (OMA), each lane,MMF	TxOMA	-4.0		4.5	dBm	1
Optical Modulation Amplitude (OMA), each lane,SMF	TxOMA	-6.0		3.5	dBm	1
Extinction Ratio	ER	3.5			dB
Relative Intensity Noise	RIN			-128	dB/Hz
Center Wavelength Range	Lane0	1264.5	1271	1277.5	nm
	Lane1	1284.5	1291	1297.5	nm
	Lane2	1304.5	1311	1317.5	nm
	Lane3	1324.5	1331	1337.5	nm
Side-Mode Suppression Ratio	SMSR	30			dB
Transmitter and Dispersion Penalty, each lane,MMF	TDP			2.6	dB
Transmitter and Dispersion Penalty, each lane,SMF	TDP			2.6	dB
Launch Power in OMA minus TDP, each lane,MMF	TxP-TDP			-6.6	dBm
Launch Power in OMA minus TDP, each lane,SMF	TxP-TDP			-8.8	dBm
Transmitter OFF Output Power	POff			-30	dBm
Optical Return Loss Tolerance				20	dB
Transmitter Reflectance				-12	dB
Transmitter Output Power Monitoring Accuracy		-3		3	dB
Transmitter eye mask definition {X1,X2,X3,Y1,Y2,Y3}	0.25,0.4,0.45,0.25,0.28,0.4
*Receiver*
Input Optical Wavelength	Lane0	1264.5	1271	1277.5	nm
	Lane1	1284.5	1291	1297.5	nm
	Lane2	1304.5	1311	1317.5	nm
	Lane3	1324.5	1331	1337.5	nm
Rx Sensitivity (OMA) per lane (BER<1E-12),SMF	R_SENS1			-11.5	dBm
Rx Sensitivity(OMA) per lane (BER<1E-12),MMF	R_SENS2			-10.5	dBm
Stressed Receiver Sensitivity (OMA) per Lane, MMF	SRS			-5.0	dBm
Stressed Receiver Sensitivity (OMA) per Lane, SMF	SRS			-8.5	dBm
Receiver Loss	RL			-20	dBm
Loss of Signal Assert	P_A	-28			dBm
Loss of Signal De-assert	P_D			-12	dBm
LOS Hysteresis	P_D- P_A	0.5		6	dB
RxPower DDMI Accuracy		-3.0		3.0	dB

Note:

1. Even if TDP is <0.9dB, the OMA min must exceed this value.

V. Memory Map and Control Registers

Compatiable with SFF-8436Rev.4.8(QSFP+).

VI. Electrical Interface Characteristics

Parameter	Symbol	Min.	Typ.	Max.	Unit	Ref.
Supply Voltage	V_CC1, V_CCT_X, V_CCR_X	3.15		3.45	V
Supply Current	I_CC			350	mA
*Transmitter*
Input different impedance	R_in	90	100	110	Ω	2
Single ended data input swing	Vin,pp	120		820	mV
Transmitter Disable Voltage	VDIS	2		V_CC	V	3
Transmitter Enable Voltage	VEN	0		0.8	V
*Receiver*
Output different impedance	R_out	90	100	110	Ω	2
Single ended data output swing	Vout,pp	340		850	mV	4
LOS Asserted	V_LOSA	2		V_CCHOST	V	5
LOS De-asserted	V_LOSD	0		0.8	V	5
Power Supply Rejection	PSR	50			mVpp

Note :

1.Maximum total power value is specified across the full temperature and voltage range.

2.Connected directly to TX data input pins. AC coupled thereafter.

3. Or open circuit.

4.Into 100Ω differential termination.

5.Loss Of Signal is LVTTL. Logic “0” indicates normal operation; logic “1” indicates no signal detected.

VII. Mechanical Specifiactions

feature

Product Features

l Supports 41.2 Gb/s aggregate bitrates

l Uncooled 4x10Gb/s CWDM transmitter

l Maximum link length of 150m on OM3, 160m on OM4, and

l 2km on Single Mode Fiber (SMF)

l Hot-pluggable QSFP+ footprint

l Duplex LC receptacles

l Power dissipation < 3.5W

l Compliant to the SFF-8636 Common Management Interface MSA

l Single 3.3V power supply

l Support Digital Diagnostic Monitor interface

l Case operating temperature

Commercial: 0°C to +70°C

Applications	Compliance
l 40GBASE Ethernet links	l QSFP+ MSA.
l Data Center interconnections	l IEEE802.3ba
	l SFF-8436

Specifications

Ordering Information

Part NO.

Bit Rate (Gbps)

Laser (nm)

Distance(km)

Media

DDMI

Connector

Temp（℃）

FSANLC23-K02C

10.3125

1271nm

1291nm

1311nm

1331nm

single-mode fiber

YES

0~70