FSANLB31-K80C_40G QSFP+_SFP Optical Transceivers_Products

FSANLB31-K80C

QSFP+ 40Gb/s 1310nm ZR4 80km DDMI

Product Features:
l Hot-pluggable QSFP+ form factor;
l Up to 11.2Gbps per channel bandwidth;
l Up to 80km transmission;
l Aggregate bandwidth of > 40Gbps;
l Power dissipation < 3.5W;
l 4 lanes MUX/DEMUX design;
l Integrated LAN WDM TOSA/ROSA;
l Compliant with 40G Ethernet IEEE802.3ba and 40G BASE-ZR4;
l QSFP MSA compliant;
l APD photo-detector;
l Single 3.3V power supply;
l Compliant with QDR/DDR Infiniband data rates;
l RoHS Compliant Part;
l Duplex LC receptacles;
l Built-in digital diagnostic functions;
l Temperature range 0°C to 70°C

Back to list

Product Overview Product Features Specifications

Overview

I. Pin Diagram

II. Pin Description

Pin	Symbol	Name/Description	Ref.
1	GND	Ground	1
2	Tx2n	Transmitter Inverted Data Input
3	Tx2p	Transmitter Non-Inverted Data Input
4	GND	Ground	1
5	Tx4n	Transmitter Inverted Data Input
6	Tx4p	Transmitter Non-Inverted Data Input
7	GND	Ground	1
8	ModSe1L	Module Select
9	ResetL	Module Reset
10	Vcc Rx	+3.3V Power supply receiver	2
11	SCL	2-wire serial interface clock
12	SDA	2-wire serial interface data
13	GND	Ground	1
14	Rx3p	Receiver Non-Inverted Data Output
15	Rx3n	Receiver Inverted Data Output
16	GND	Ground	1
17	Rx1p	Receiver Non-Inverted Data Output
18	Rx1n	Receiver Inverted Data Output
19	GND	Ground	1
20	GND	Ground	1
21	Rx2n	Receiver Inverted Data Output
22	Rx2p	Receiver Non-Inverted Data Output
23	GND	Ground	1
24	Rx4n	Receiver Inverted Data Output
25	Rx4p	Receiver Non-Inverted Data Output
26	GND	Ground	1
27	ModPrSL	Module Present
28	IntL	Interrupt
29	VccTx	+3.3V Power supply transmitter	2
30	Vcc1	+3.3V Power Supply	2
31	LPMode	Low Power Mode
32	GND	Ground	1
33	Tx3p	Transmitter Non-Inverted Data Input
34	Tx3n	Transmitter Inverted Data Input
35	GND	Ground	1
36	Tx1p	Transmitter Non-Inverted Data Input
37	Tx1n	Transmitter Inverted Data Input
38	GND	Ground	1

Notes：

1. Circuit ground is internally isolated from chassis ground.

2. VccRx, Vcc1 and VccTx are the receiver and transmitter power suppliers and shall be applied concurrently. Recommended host board power supply filtering is shown below. VccRx, Vcc1 and VccTx may be internally connected within the QSFP transceiver module in any combination. The connector pins are each rated for maximum current of 500mA.

III. Absolute Maximum Ratings

Parameter	Symbol	Min.	Typ.	Max.	Unit	Ref.
Storage Temperature	T_S	-40		85	ºC
Storage Ambient Humidity	H_A	0		85	%
Maximum Supply Voltage	V_CC1, V_CCT_X, V_CCR_X	-0.5		3.6	V
Supply Voltage	V_CCT,R	-0.5		4.0	V

IV. Recommended Operating Environment

Parameter	Symbol	Min.	Typ.	Max.	Unit	Ref.
Case operating Temperature	T_C	0		70	ºC
Supply Voltage	V_CCT,R	3.13	3.3	3.47	V
Supply Current	I_CC			1000	mA
Power Dissipation	PD			3.5	W

V. Optical Characteristics

Parameter	Symbol	Min.	Typ.	Max.	Unit	Ref.
Transmitter
Signaling Speed per Lane			10.3125	11.2	Gbps
Total Average Launch Power	P_OUT			10.5	dBm
Average Output Power per lane	P_OUT	4		7	dBm
Transmit OMA per Lane	TxOMA	0.3		5.0	dBm	1
Extinction Ratio	ER	5.5	6.5		dB
Center Wavelength	λC	1294.53 1299.02 1303.54 1308.09	1295.56 1300.05 1304.58 1309.14	1296.59 1301.09 1305.63 1310.19	nm
Sidemode Suppression ratio	SMSR	30			dB
Transmitter and Dispersion Penalty	TDP			2.6	dB
Relative Intensity Noise	RIN			-128	dB/Hz	2
Transmitter OFF Output Power	POff			-30	dBm
Optical Return Loss Tolerance				12	dB
Transmitter eye mask definition {X1,X2,X3,Y1,Y2,Y3}		0.25,0.4,0.45,0.25,0.28,0.4
Receiver
Damage Threshold	THd	0			dBm	2
Average Power at Receiver Input, each Lane	R	-24		-6	dBm
Receive Electrical 3dB upper Cut off Frequency, each Lane				12.3	GHz
RSSI Accuracy		-2		2	dB
Receiver Power(OMA), each Lane				-4	dBm
Receiver Reflectance	Rfl			-26	dBm
Loss of Signal Assert	P_A	-35			dBm
Loss of Signal De-assert	P_D			-25	dBm
LOS Hysteresis	P_D- P_A	0.5			dB

Notes:

1. Minimum value is informative.

2. 12dB Reflection.

VI. Electrical Interface Characteristics

Parameter	Symbol	Min.	Typ.	Max.	Unit	Ref.
Signaling Speed per Lane			10.3125	11.2	Gbps
Power Consumption			2.5	5	W
Supply Current	I_CC		0.75	1.3	A
Control I/O Voltage-High	VIH	2		V_CC	V
Control I/O Voltage-Low	VIL	0		0.7	V
Inter-Channel Skew	TSK			150	Ps
RESETL Duration			10		Us
RESETL De-assert time				100	ms
Power On Time				100	ms
Transmitter
Single Ended Output Voltage Tolerance		0.3		4	V	1
Common mode Voltage Tolerance		15			mV
Transmit Input Diff Voltage	VI	150		1200	mV
Transmit Input Diff Impedance	ZIN	85	100	115
Data Dependent Input Jitter	DDJ		0.3		UI
Receiver
Single Ended Output Voltage Tolerance		0.3		4	V
Rx Output Diff Voltage	Vo	370	600	950	mV
Rx Output Riseand Fall Voltage	Tr/Tf			35	ps
Total Jitter	Tj		0.3		UI

Notes :

1. 20%~80%.

VI. Recommended Interface Circuit

VII. Diagnostic Monitoring Interface

VIII. Recommended Circuit

IV. Mechanical Specifiactions

feature

Product Features

l Hot-pluggable QSFP+ form factor

l Up to 11.2Gbps per channel bandwidth

l Up to 80km transmission

l Aggregate bandwidth of > 40Gbps

l Power dissipation < 3.5W

l 4 lanes MUX/DEMUX design

l Integrated LAN WDM TOSA/ROSA

l Compliant with 40G Ethernet IEEE802.3ba and 40G BASE-ZR4

l QSFP MSA compliant

l APD photo-detector

l Single 3.3V power supply

l Compliant with QDR/DDR Infiniband data rates

l RoHS Compliant Part

l Duplex LC receptacles

l Built-in digital diagnostic functions

l Temperature range 0°C to 70°C

Applications	Compliance
40G BASE-ZR4	QSFP MSA.
Rack to rack	IEEE802.3ba
Data centers Switches and Routers	RoHS

Specifications

Ordering Information

Part NO.	Bit Rate (Gbps)	Laser (nm)	Distance(km)	Media	DDMI	Connector	Temp（℃）
FSANLB31-K80C	10.3125*4	1310	80	single-mode fiber	YES	LC	0~70